CB Radio - Uniden Bearcat 880 CB Radio w/ CLEAN TUNE UP by 𝘽𝙚𝙡𝙡𝙨 🔔 𝘾𝘽!!!

Description: BC880Mobile CB Radio Tuned up values on these watt metersDosyBird RMS* Bird 43PAM6w6w6wPEAK AM13w7w30w* The most informative meter and the one we use. GENERAL Channel: 40Frequency Range:26.965 - 27.405 MHzFrequency Control:PLL Synthesizer 18Antenna Impedance:50 ohmsPower Input:13.8VDCCurrent Drain TX: AM Full Modulation: 2.2A (max)RX:At no signal: 650mAOperating Temperature:-22°F to 140°F (-30°C to 60°C)Accessories:DC Power Cord Microphone Microphone Hanger Mounting BracketSize(W x D x H): 6.3 in. x 6.3 in. x 2.2 in. (without knobs and jacks) THIS IS A FACTORY CLAIM ANDWE MEASURE IT DIFFERENTLY. (WxDxH) 7.25 in x 7.5 in x 2.2 in(without Knobs and Jacks)(9" depth with knobs and jack)Weight:2.2 PoundsTRANSMITTER Output Power:4 wattsEmission Type:6A3Hum and Noise:Better than 40 dBFrequency Tolerance:±0.002%Modulation Percentage(Peak): 100%Spurious Rejection:-70 dBOutput Impedance:50 ohm, unbalancedRECEIVER Sensitivity at 10 dB S+N/N:0.5 µVSensitivity at 500 mW Audio Output:0.5 µVSquelch Threshold:0.5 µVAntenna Impedance: 50 ohmsSquelch Tight:1000 µVSignal Meter S-9:100 µVAudio Output Power (max.): 5 wattsAudio Output (10% Dist.):4 wattsAdjacent Channel Rejection:55dBImage Rejection:65dBInternal Speaker Impedance:16 ohmsExternal Speaker Impedance:8 ohmsPUBLIC ADDRESS Output Power at 10% Distortion:4 wattsSpecifications shown are typical and subject to change without notice. The Most Trusted Name in CB Radios. It's tough and powerful with a large easy-to-read display and exciting new features including 7 Color Backlighting, Noise Cancelling Mic, and Wireless Mic Compatibility.7-Color BacklightingNoise Cancelling MicTalkbackRadio Diagnostics6 Pin Noise Canceling MicWireless Mic CompatibleDigital SRF / SWR MeterFrequency DisplayNOAA WeatherSquelch ControlANL / NoiseBlankerMemory ScanRF GainMicrophone GainInstant Channel 9/19CB / PAChannel IndicatorIncludes 6 Pin to 4 Pin AdapterLaser Etched KeysExtra Long Mic CordDimmer Switch Day / Night View of the front: 1. Volume Control knob with Power On/Off. 2. SQUELCH knob: 3. S/RF/CAL/SWR Meter: 4. Channel Number display. 5. Operation buttons and associated LEDs: Talkback: Talkback lets you monitor yourself when transmitting. With Talkback active, press PTT and adjust the volume with the Volume Control knob. (Levels 00 - 15) MIC Gain: Adjusts microphone sensitivity. Delivers up to 100% modulation. With MIC Gain active, press PTT and adjust the gain levels with the Volume Control knob. (Levels 00 - 04) Weather: Press to toggle between Weather and CB channels. Turn Channel Selector to cycle through the 7 weather channels. Press and hold to turn Weather Alert on and off. ALERT displays. Day/Night: Adjusts LCD backlight sensitivity between Day and Night modes.6. Channel Selector/MENU/OK. Press the inner MENU/OK button to select a menu option or other selection. Turn the outer Channel Selector knob to: Select channels Select menu modes Change scan resume direction (up or down) Control Talkback volume Control Mic gain level Control Calibration volume7. Microphone socket. 8. Indicators turn on when the function is turned on. 9. S/RF/CAL/SWR: Push to to check RF signal strength, calibration, and SWR reading. 10. CB/PA: Selects CB (Citizens Band) or PA (Public Address). Do not use the PA function unless an external speaker is connected. 11. MEM/SCAN: Press to start or stop scanning modes [All Channel Scan (see page 10) and Memory Scan (see page 12)]. Press and hold to set or clear channel memory while in Memory mode. 12. 9/19/NORM: Press to switch between emergency channel 9, channel 19, and standard CB channels. 13. Frequency Display: Displays the MHz of the selected channel. Also displays menu options. 14. ANL: Turns ANL (Automatic Noise Limiter) feature on and off. ANL reduces external noise. 15. NB: Turns NB (Noise Blanker) feature on and off. NB reduces interference from vehicle ignition systems. 16. RF Gain knob: Improves reception in strong signal areas. View of the back: 17. Antenna socket: Connects antenna to the unit. 18. PA SP: Connects optional external 8-ohm, 4-watt speaker for use as a public address system. To prevent acoustic feedback, separate the microphone from the speaker when operating the PA at high output levels. 19. EXT. SP: Connects an 8-ohm 4-watt speaker to remotely monitor the receiver. When the external speaker is plugged in, the internal speaker is off. 20. POWER: Connects DC power to transceiver. 21. Fuse. 22. PTT: Push-to-Talk.

Price: 199.5 USD

Location: Fort Lauderdale, Florida

End Time: 2024-09-15T17:20:30.000Z

Shipping Cost: N/A USD